the information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. this documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. it is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. neither schneider electric industries sas nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein. 10/8/2011 1 product data sheet characteristics ATS22D47Q soft starter-ats22-control 220v-power 230v(11kw)/400...440v(22kw) main range of product altistart 22 product or component type soft starter product destination asynchronous motors product specific application severe and standard applications component name ats22 network number of phases 3 phases power supply voltage 230...440 v (- 15...10 %) motor power kw 11 kw at 230 v 22 kw at 400 v 22 kw at 440 v factory setting current 42 a power dissipation in w 48 w for standard applications utilisation category ac-53a type of start start with torque control (current limited to 3.5 in) icl nominal current 47 a (connection in the motor supply line) for standard applications ip degree of protection ip20 complementary assembly style with heat sink function available internal bypass power supply voltage limits 195...484 v power supply frequency 50...60 hz (- 10...10 %) network frequency 45...66 hz device connection in the motor supply line to the motor delta terminals control circuit voltage 220...230 v -15...10 % at 50/60 hz control circuit consumption 20 w discrete output number 2 discrete output type (r1)relay outputs 230 v running, alarm, trip, stopped, not stopped, starting, ready, c/o (r2)relay outputs 230 v running, alarm, trip, stopped, not stopped, starting, ready, c/o minimum switching current relay outputs 100 ma at 12 v, dc maximum switching current relay outputs 5 a at 250 v, ac resistive load, cos phi = 1 relay outputs 5 a at 30 v, dc resistive load, cos phi = 1 relay outputs 2 a at 250 v, ac inductive load, cos phi = 0.4, l/r = 20 ms relay outputs 2 a at 30 v, dc inductive load, l/r = 7 ms discrete input number 3 discrete input type (li1, li2, li3)logic 5 ma 4.3 kohm discrete input voltage 24 v (<= 30 v) discrete input logic (li1, li2, li3)positive logic state 0 < 5 v and < 2 ma state 1 > 11 v and > 5 ma output current 0.4...1 icl adjustable ptc probe input 750 ohm communication port protocol modbus connector type 1 rj45 communication data link serial physical interface rs485 multidrop
2 transmission rate 4800, 9600 or 19200 bps max nodes number 31 protection type phase failure on line thermal protection on motor thermal protection on starter marking ce type of cooling forced convection operating position vertical +/- 10 degree product weight 7 kg environment electromagnetic compatibility conducted and radiated emissions conforming to iec 60947-4-2 level a damped oscillating waves conforming to iec 61000-4-12 level 3 electrostatic discharge conforming to iec 61000-4-2 level 3 immunity to electrical transients conforming to iec 61000-4-4 level 4 immunity to radiated radio-electrical interference conforming to iec 61000-4-3 level 3 voltage/current impulse conforming to iec 61000-4-5 level 3 standards en/iec 60947-4-2 product certifications ccc csa c-tick gost ul vibration resistance 1 gn (f = 13...200 hz) conforming to en/iec 60068-2-6 1.5 mm (f = 2...13 hz) conforming to en/iec 60068-2-6 shock resistance 15 gn for 11 ms conforming to en/iec 60068-2-27 noise level 45 db pollution degree level 2 conforming to iec 60664-1 relative humidity <= 95 % without condensation or dripping water conforming to en/iec 60068-2-3 ambient air temperature for operation -10...40 c without derating > 40...< 60 c with current derating 2.2 % per c ambient air temperature for storage -25...70 c operating altitude <= 1000 m without derating > 1000...< 2000 m with current derating of 2.2 % per additional 100 m rohs eur status compliant rohs eur conformity date 0938
3 product data sheet dimensions drawings ATS22D47Q frame size a dimensions
4 product data sheet mounting and clearance ATS22D47Q precautions standards the altistart 22 soft starter is compliant with pollution degree 2 as defined in nema ics1-1 or iec 60664-1. for environment pollution degree 3, install the altistart 22 soft starter inside a cabinet type 12 or ip54. danger hazard of electric shock, explosion, or arc flash ats22 soft starters are open devices and must be mounted in a suitable enclosure. failure to follow these instructions will result in death or serious injury. air circulation leave sufficient free space to help the air required for cooling purposes to circulate from the bottom to the top of the unit. overheating to avoid the soft starter to overheat, respect the following recommendations: mount the altistart 22 soft starter within 10 of vertical. do not locate the altistart 22 soft starter near heat radiating elements. electrical current through the altistart 22 soft starter will result in heat losses that must be dissipated into the ambient air immediately surrounding the soft starter. to help prevent a thermal fault, provide sufficient enclosure cooling and/or ventilation to limit the ambient temperature around the soft starter. if several soft starters are installed in a control panel, arrange them in a row. do not stack soft starters. heat generated from the bottom soft starter can adversely affect the ambient temperature around the top soft starter. mounting
5 connection between the fan and the altistart 22 soft starter 1 altistart 22 soft starter 2 fan wall mounted or floor-standing enclosure with ip 23 degree of protection introduction to help proper air circulation in the soft starter, grilles and forced ventilation can be installed. ventilation grilles forced ventilation unit
6 product data sheet connections and schema ATS22D47Q power terminal cage style 1 ground connection power connections, minimum and maximum wiring capabilities, tightening torque iec cable ul cable power supply and output to motor size/gauge min 2.5 mm 12 awg max 16 mm 4 awg tightening torque min 3 n.m 26.25 lb.in max 3 n.m 26.25 lb.in strip length 10 mm 0.4 in. power connections, minimum required wiring section iec cable mm2 (cu 70c/158f) (1) ul cable awg (cu 75c/167f) (1) 10 6 230 vac control, logic inputs (li) 24 vdc, 3-wire control
7 with line contactor, freewheel or controlled stop 230 vac control, logic inputs (li) 24 vdc, 2-wire control,freewheel stop connection in the motor delta winding in series with each winding wiring ats22 soft starters connected to motors with the delta connections can be inserted in series in the motor windings. the following wiring requieres particular attention. it is documented in the altistart 22 soft start - soft stop unit user manual. please contact schneider electric commercial organisation for further informations.
8 example a 400 v - 110 kw motor with a line current of 195 a (nominal current for the delta connection). the current in each winding is equal to 195/1.5 or 130 a. the rating is determined by selecting the soft starter with a permanent nominal current (icl) just above this current.
9 product data sheet performance curves ATS22D47Q motor thermal protection - cold curves curves a class 10 b class 20 c class 30 trip time for a standard application (class 10) 3.5 ln 32 s trip time for a severe application (class 20) 3.5 ln 63 s trip time for a severe application (class 30) 3.5 ln 95 s
10 motor thermal protection - warm curves curves a class 10 b class 20 c class 30 trip time for a standard application (class 10) 3.5 ln 16 s trip time for a severe application (class 20) 3.5 ln 32 s trip time for a severe application (class 30) 3.5 ln 48 s
|
